Same day or next day service
£No hidden costs
Fully insured
365 day guarantee*
Nationwide
Poole

Power Cut in Poole

A power cut at a domestic property in Poole can have several distinct causes, and identifying whether the loss of supply is internal or external is the first practical step.

Call us on 01202 000000 (placeholder - not in service)

Power Cut

A power cut at a domestic property in Poole can have several distinct causes, and identifying whether the loss of supply is internal or external is the first practical step. If neighbouring properties have also lost power, the cause is likely a fault on the local distribution network and the Distribution Network Operator (DNO) should be contacted.

The electricity distribution network for the Dorset and Poole area is operated by Scottish and Southern Electricity Networks (SSEN). An outage affecting one property can still originate in the network supply or service cable.

Other possible causes include a tripped protective device, meter or service-fuse fault, or internal wiring defect. Call 105 for a suspected network fault.

Do not open the consumer unit or disturb sealed meter or service-fuse equipment. Do not reset a device if there is heat, burning, water ingress, sparking or visible damage.

Where there are no warning signs, follow the manufacturer's safe user instructions and disconnect suspected appliances only if safe. If a device trips again or will not hold, leave it off and obtain qualified help rather than repeatedly resetting it.

Do not attempt to interfere with the sealed cut-out or meter equipment, as these are the property of the network operator and energy supplier respectively. A loss of power affecting only part of the property, such as a single room or a group of sockets, is often caused by a tripped circuit breaker or RCD protecting that circuit.

The pattern alone does not prove that the fault is internal. Call 105 if a supply fault is suspected or the cause is unclear; internal wiring and appliance faults need a qualified electrician once supply responsibility is established.

Emergency electrical assistance covers situations where loss of power affects safety or essential equipment in the property. For a suspected network outage, contact 105.

For a life-threatening emergency call 999 or 112. For internal electrical work, use the enquiry form to describe the fault; submitting a form does not confirm attendance or supply restoration.

Signs the power cut may be an internal fault

⚠️

Only Your Property Is Affected

One affected property can have an internal fault or a problem in its network service connection. Report a suspected supply fault on 105; do not disturb sealed network or metering equipment or repeatedly reset protective devices.

⚠️

Partial Power Loss

Some circuits working while others do not can indicate a tripped protective device, an internal wiring or appliance fault, or a supply problem. That pattern alone does not establish responsibility. Call 105 for a suspected or unclear supply fault. Leave a device that trips again off and obtain qualified investigation rather than repeatedly resetting it.

⚠️

Burning Smell or Scorch Marks

A burning smell near the consumer unit, switches or sockets, or visible scorch marks around accessories, indicates a serious fault. Do not attempt to reset any devices. Leave the consumer unit alone, avoid using the affected circuits, and arrange for an electrician to attend promptly. If there is a fire, get out, stay out and call 999.

How an emergency power cut assessment works

1

Initial Diagnosis

The electrician checks the consumer unit, the incoming supply and the individual circuits to establish whether the fault lies at the cut-out, the meter, the consumer unit itself or in the wiring of a specific circuit.

2

Fault Isolation

Individual circuits are tested to identify which one is carrying the fault. Equipment and wiring on that circuit are then checked to locate the specific cause, whether that is a wiring defect, a faulty accessory or an appliance problem.

3

Repair and Restoration

Once an internal fault is identified and the work agreed, the electrician carries out the appropriate repair and tests it before returning the affected circuit to use. Network or metering faults are referred to the responsible provider. Electrical certification and any separate notification record depend on the actual work.

FAQs About Power Cut

How do I tell whether a power cut is on the street or inside my property?
Neighbouring outages suggest a network problem, but one affected property does not prove the fault is internal: a service cable or network connection can supply just one property. Call 105 for suspected network faults. In Poole the distribution network is operated by SSEN. Do not open sealed network or metering equipment.
What should I check in my consumer unit after a power cut?
You may look at the consumer unit without opening or dismantling it. Do not reset a device if there is heat, burning, sparking, water ingress or visible damage. Follow the manufacturer's safe user instructions only where there are no warning signs. A device that trips again or will not hold needs qualified investigation; do not repeatedly reset it.
What is an RCD and why does it trip?
A residual current device (RCD) is a safety device in the consumer unit that detects imbalances in the electrical current flowing through a circuit, which can indicate a fault or accidental contact with live conductors. It trips to interrupt the circuit before a dangerous condition develops. Common causes of RCD tripping include faulty appliances, water ingress into outdoor fittings, and deteriorating cable insulation.
What should I do if I cannot restore power by resetting breakers?
Stop resetting a device that trips again or will not hold. Failure to restore power does not establish that the fault is inside the property. Call 105 if a network or service-supply fault is suspected or the supply cause is unclear; the network operator can advise. A qualified electrician investigates internal wiring or appliance faults once the supply responsibility is established. Do not open sealed equipment or unplug hot, damaged or sparking fittings. For an immediate threat to life, call 999 or 112.
Is the main switch the same as a tripping protective device?
A main isolating switch is normally a manually operated switch, whereas an RCD, RCBO or circuit breaker can trip because of a fault. They should not be confused. Do not force a device to stay on, open the unit or repeatedly reset protection. If you are unsure which device has operated, leave it alone and seek qualified advice.
What should I do if a power cut is affecting essential equipment?
If there is an immediate threat to life, call 999 or 112 and follow the medical equipment provider's emergency plan. Report a suspected network outage on 105 and explain any medical dependency. The DNO's Priority Services Register may provide additional support, but it does not ensure uninterrupted supply. Do not rely on this site's enquiry form for an immediate medical emergency.

More Emergency Electrician services

Tripped Fuse BoardBurning Smell

Other services in Poole

🏠 Fuse Board / Consumer Unit Replacement ⚡ Rewiring 📋 Electrical Inspections & Testing 🔌 Lighting & Sockets 🏠 EV Charger Installation

Areas

Contact

Describe the problem and provide your contact details. Sending an enquiry does not confirm a booking.

01202 000000 (placeholder - not in service)
Use the enquiry form; the telephone number is a placeholder.
Service area: Poole.

Quick quote request

📞 Call Now 💬 Enquire